ZXDSL 9210 Commissioning Manual

Basic Command
1. Login : admin
Password: admin
Login to the ZXDSL CLI console, default username is admin and the password is admin.
2. DSL#Show card
Show all of the card and their status on the ZXDSL 9210
3. DSL# erase
Delete all of the configuration that contain on the ZXDSL 9210. Please be careful to used this command, because it’s will erased all of the configuration on your system.
4. DSL#reboot
Reboot the ZXDSL 9210 and restart all of the board. Please be careful to used this command, because it’s will restart all of the board and the system will be down for a few second.

Change the ZXDSL 9210 Inband MAC address and identifier board
5. DSL#enable
Password : zxedsl
DSL$ debug module 12345
DSL$ debug module 888999 p1 00:d0:d0:00:00:01 (3 no terakhir => max 92:FF:FF)
DSL$ disable
DSL#reboot
This command used only if you are necessary to change the inband MAC address, if you first time build the ZXDSL 9210 network with more than one DSLAM please make sure there are no conflict MAC address on the each Network element(NE) on the same network. After you’re change this MAC address it’s will be take the effect after you’re reboot the system. After you change the MAC address and reboot the system, make sure the inband MAC address is already changed by type :
DSL# show ip subnet
6. DSL#config card slot 1 cardtype ASNVC2
7. DSL#config card slot 3 cardtype ATIGN ---spliter

Enable the PVLAN mode and initialize the uplink port
8. DSL#Configuration
[DSL(config)#pvlan-mode enable -> enable the pvlan mode]
DSL(config)#pvlan-mode uplink-port 1/1 ->initialize the uplink port for Gigabit Ethernet (biasanya ada di up-link 9/1 control modul yah..)
DSL(config)#pvlan-mode uplink-port-group 13/2 ->initialize the uplink port for Fe or Eth
DSL(config)#Exit
DSL#Copy running-config startup-config -> Save and commit all of the config

DSL#reboot -> after you’re enable the pvlan mode, it’s will be take the effect after you’re reboot the system

Add the Inband IP Address to the ZXDSL 9210
9. DSL#Configuration
DSL(config)#IP subnet 150.168.0.2 255.255.254.0 name dslam1
DSL(config)#exit
And then to make sure the IP address already adding to the ZXDSL 9210 type:
DSL#Show ip subnet

Add the Vlan and put the port into the Vlan
10. DSL#configuration
DSL(config)#add-vlan 2 -> add vlan 2
DSL(config)#add-vlan 3 -> add vlan 3
DSL(config)#vlan 2 1/1 tag -> put port 1/1 as an uplink to the switch into vlan 2 as a management vlan and tag it
DSL(config)#vlan 3 1/1 tag -> put port 1/1 as an uplink to the switch into vlan 3 as a PPPoe vlan and tag it
And then make sure the vlan are already exist and the port are already exist on the vlan by type:
DSL#Show vlan -> show all the vlan that already exist on the system
DSL#Show vlan 2-> show all the port(tag or untag) that are already exist on the vlan 2
DSL#Show vlan 3 -> show all the port(tag or untag) that are already exist on the vlan 3

Configure the adsl user on the ATIGN board
11. DSL#configure slot adsl 3
DSL(cfg-slot-adsl-3)#trap control enable -> to make if the subscriber in this board is on and then this board will know it
DSL(cfg-slot-adsl-3)#no shutdown
DSL(cfg-slot-adsl-3)#exit
DSL(config)#slot adsl 3
DSL(cfg-slot-adsl-3)#pvid 3 ->because of we configure the ADSL subscriber as an untag port so we need to add the pvid
DSL(cfg-slot-adsl-3)#atm pvc 8:81 ->configure the PVC(VCI/VCI) into the subscriber board
DSL(cfg-slot-adsl-3)#exit
DSL(config)#show atm vc slot 3 ->make sure the PVC are already exist at the subscriber board
DSL(config)#vlan 3 3/1-32 untag -> put the subscriber port into the vlan 3 as a subscriber vlan and untag it


Create the ADSL profile and apply the profile to the ADSL subscriber
12. DSL(config)#adsl-profile adsl512k -> this fist command is to created your profile. And then System will ask you this profile didn’t created before, are you sure want to create this profile? You should answer yes.
DSL(config)# adsl-profile adsl512k -> the second command is to configure your profile. And then system will ask you to input all of your configuration, but the most important you should configure the uplink and downlink rate:
• Downlink rate :
Atuchan conf fast max Tx rate [0-132040] (Def:8128) : 1024
Atuchan conf interleave max Tx rate [0-132040] (Def:8128) : 1024
• Uplink rate:
Aturhan conf fast max Tx rate [32-1536] (Def:1024) : 128
Aturhan conf interleave max Tx rate [32-1536] (Def:1024): 128
And then to make sure your ADSL profile is already created successfully type:
DSL#Show adsl profile -> show all adsl profile
DSL#Show adsl profile adsl512k -> show detail the adsl512k profile
DSL(config)#interface adsl 3/1 ->enter the adsl slot 3 port 1 to configure it
DSL(cfg-if-adsl-3/1)#adsl profile adsl512k ->apply the profile to adsl port
DSL(config)#slot adsl 3 -> enter the adsl slot 3 to configure it
DSL(cfg-slot-adsl-3)#adsl profile adsl512k ->apply the profile to adsl slot

Configure the ZXDSL 9210 SNMP server
13. DSL(config)#snmp-server host 10.10.10.1 private ->initialize the snmp server ip address to the ZXDSL 9210
DSL#show snmp -> show the snmp server ip address that you’re already initialize to the ZXDSl 9210
DSL(config)#ip route 0.0.0.0 0.0.0.0 192.168.0.1 -> add the static route to the ZXDSL 9210. This command is used only if the SNMP server Ip address is not in the same network segment with the ZXDSL 9210 ip address.

Configure Uplink port with the STP(Spanning tree protocol) features (gw blum pernah coba yang ini !!!)
14. kayanya siy niy beda card yang di slot, klo yang ada kan ASNVC2 dan PVNA buat splitter.
15. for example we want to configure the EICG board port 1 on the slot 1 and 2 as an uplink port with the STP features where EICG slot 1 port 1 and EICG slot 2 port 1 will be as a redundant uplink port.
DSL#show spanning-tree -> to show the STP features on the ZXDSL 9210 is already enable or not, if the status of STP is disable you should be enable it by type:
DSL#Config spanning-tree enable -> enable the STP features on the system
DSL#show spanning-tree -> make sure the STP features on the system is already enable. And please check the priority on this STP, the value of priority should be less then the priority value on the switch (Ethernet aggregator).
DSL#config interface Ethernet 1/1-> enter EICG slot 1 port 1 to configure it
DSL(cfg-if-eth-1/1)#spanning-tree enable->enable the STP features on the EICG slot 1 port 1.
DSL(cfg-if-eth-1/1)#show spanning-tree interface 1/1 -> make sure the STP features on the slot 1 port 1on is already enable

DSL#config interface Ethernet 2/1-> enter EICG slot 2 port 1 to configure it
DSL(cfg-if-eth-2/1)#spanning-tree enable->enable the STP features on the EICG slot 2 port 1.
DSL(cfg-if-eth-2/1)#show spanning-tree interface 2/1 -> make sure the STP features on the slot 2 port 1on is already enable

After you are already configure the STP features in both of port, you should be check the status of link in this port.
DSL(cfg-if-eth-1/1)#show spanning-tree interface 1/1 -> look the status of STP, there are 3 kind of status on this STP port :
1. blocking -> means the port is blocking and can’t transfer the packet
2. learning -> means the port still learning the other port, please waiting for a few minutes.
3. forwarding -> means the STP port is already active and ready to transfer the packet.
DSL(cfg-if-eth-1/2)#show spanning-tree interface 1/2 -> look the status of STP, the normal condition if port(1/1) and port (1/2) both of them as an STP port, one of them will be blocking and one of the other will be forwarding.